banner



How To Tie Dye Around A Logo

Joan
Statuary Feedback Medal for All Time! 186 Feedbacks

Apr 29, 2010 0 establish this helpful

I would just pass information technology off as a tie-dyed shirt. If you have to accept more bleach spots on it to this, that is what I would do. I have never had much success dyeing items that had bleach spots on them, they don't terminate upwards the same color as the rest of the item.

April thirty, 2010 0 establish this helpful

I'd forget the dying and go with bleaching all over. I had nothing to lose when I bleached an olive sweatshirt because of bleach spots. All but the stitching bleached and it is admittedly lovely, very classy and I establish that I had discovered a new lime'ish-xanthous that gets compliments each fourth dimension I wear it.

The bleached spot(s) AND the keepsake might do well to "pigment" until saturated with a pocket-sized artist's brush using Scotchguard water repellent (spray exterior into the lid to assemble a puddle of it for forepart and back of the keepsake and spot(due south)).

And then, let information technology dry a full 24 hrs. earlier bleaching, using no detergent until yous accomplish an even lightening. Fifty-fifty if the Scotchguard washes out as a result, you will have given it all a couple of terminal rinses.

Wash every bit usual only after you have accomplished a similar lightening every bit is the spot(s), your guideline. Be extra careful not to put besides much Scotchguard on your brush or q-tip so you stay within the spot edges, keeping in mind that the liquid Scotchguard might run if yous accept your brush or q-tip besides full.

Test it on a rag or thickly folded paper towel first to become the hang of it and to see how much bleeds into the non-bleached areas around the q-tip or brush size.

Think back to the amount of bleach that yous likely used in a washer load that originally bleached it? And the temp of the bleach at the time. Was the bleach added to a dry shirt or wet one? Think it through very well first.

Or was it an accidental drip? If an blow, was it total force? If diluted, try to remember the approx. mixture/dilution and employ that same formula, temp. time, again.

The best you can hope for is an all-over color like the spot(southward). The worst is that y'all may take to dry the whole affair, Scotchguard the spot(due south) again, and echo the process until you succeed.

I remember that I still have a slight variation divergence in color from the spots I had, just when the whole garment is lighter, it's a MUCH less noticeable deviation that merely I can tell.

Good luck and God anoint y'all. " - "

May 2, 2010 1 institute this helpful

You might be able to apply the Batik method:

Melt articulate paraffin wax in a double banality filled with water in the bottom.
Pigment over your design with the wax. Make sure the wax penetrates the cloth completely (you should see it on the back of the material).
Where the wax goes, there will be no dye.
Let the wax cool.
Put on a pair of prophylactic gloves.
Prepare dyes or inks as suggested by the manufacturer. Use absurd dyes so they won't melt the wax onto the fabric.
Dye the cloth. Immerse it for about 20 seconds.
Rinse it in cool water to remove excess dye. If the color isn't dark enough, dye it again.

Allow it to air dry out by hanging information technology upward.
Remove the wax, either by scraping it off or past ironing it between a few paper towels and newspaper (this can exist washed while the fabric is still wet).

Reply Was this helpful? 1

Source: https://www.thriftyfun.com/tf31590116.tip.html

0 Response to "How To Tie Dye Around A Logo"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel